IPv6 And OSPFv3 Over DMVPN - Revision history

Casey at 02:34, 8 April 2015

2015-04-08T02:34:55Z

Casey at 04:14, 7 April 2015

2015-04-07T04:14:31Z

Casey at 04:07, 7 April 2015

2015-04-07T04:07:40Z

Casey at 04:07, 7 April 2015

2015-04-07T04:07:24Z

Casey: Created page with "Once you've got your DMVPN up and running, as shown in DMVPN, you can enable IPv6 and OSPFv3. Note that the config is largely the same as the IPv4 version. The critical ..."

2015-04-07T04:04:43Z

Created page with "Once you've got your DMVPN up and running, as shown in DMVPN, you can enable IPv6 and OSPFv3. Note that the config is largely the same as the IPv4 version. The critical ..."

New page

Once you've got your DMVPN up and running, as shown in [[DMVPN]], you can enable IPv6 and OSPFv3.

Note that the config is largely the same as the IPv4 version. The critical difference is the references to the link-local addresses (FE80::). Without these defined, OSPF will have issues maintaining adjacencies. I've also kept the global addresses mentioned (2001:DB8:DDDD::), mostly for things like pinging and SSH.

<PRE>
ipv6 unicast-routing
ipv6 cef
!
interface Tunnel0
description DMVPN
ipv6 address FE80::1 link-local
ipv6 address 2001:DB8:DDDD::1/64
ipv6 mtu 1400
ipv6 nhrp map multicast dynamic
ipv6 nhrp map multicast 203.0.113.28
ipv6 nhrp map FE80::2/128 203.0.113.28
ipv6 nhrp map 2001:DB8:DDDD::2/128 203.0.113.28
ipv6 nhrp network-id 1
ipv6 nhrp holdtime 180
ipv6 nhrp nhs FE80::2
ipv6 nhrp nhs 2001:DB8:DDDD::2
ipv6 nhrp registration timeout 60
ipv6 nhrp shortcut
ipv6 nhrp redirect
ipv6 ospf network broadcast
ipv6 ospf priority 128
ipv6 ospf 1 area 0
!
ipv6 router ospf 1
router-id 10.10.10.1
</PRE>

← Older revision		Revision as of 02:34, 8 April 2015
Line 1:		Line 1:
−	Once you've got your DMVPN up and running, as shown in [[DMVPN]], you can enable IPv6 and OSPFv3.	+	Once you've got your DMVPN up and running, as shown in the [[DMVPN]] article, you can enable IPv6 and OSPFv3.

	Note that the config is largely the same as the IPv4 version. The critical difference is the references to the link-local addresses (FE80::). '''Without these defined, OSPF will have issues maintaining adjacencies'''. I've also kept the global addresses mentioned (2001:DB8:DDDD::), mostly for things like pinging and SSH.		Note that the config is largely the same as the IPv4 version. The critical difference is the references to the link-local addresses (FE80::). '''Without these defined, OSPF will have issues maintaining adjacencies'''. I've also kept the global addresses mentioned (2001:DB8:DDDD::), mostly for things like pinging and SSH.

@@ Line 1: / Line 1: @@
 Once you've got your DMVPN up and running, as shown in [[DMVPN]], you can enable IPv6 and OSPFv3.
-Note that the config is largely the same as the IPv4 version.  The critical difference is the references to the link-local addresses (FE80::).  Without these defined, '''OSPF will have issues maintaining adjacencies'''.  I've also kept the global addresses mentioned (2001:DB8:DDDD::), mostly for things like pinging and SSH.
+Note that the config is largely the same as the IPv4 version.  The critical difference is the references to the link-local addresses (FE80::).  '''Without these defined, OSPF will have issues maintaining adjacencies'''.  I've also kept the global addresses mentioned (2001:DB8:DDDD::), mostly for things like pinging and SSH.
 <PRE>

@@ Line 3: / Line 3: @@
 Note that the config is largely the same as the IPv4 version.  The critical difference is the references to the link-local addresses (FE80::).  '''Without these defined, OSPF will have issues maintaining adjacencies'''.  I've also kept the global addresses mentioned (2001:DB8:DDDD::), mostly for things like pinging and SSH.
 <PRE>
 ipv6 unicast-routing
@@ Line 29: / Line 30: @@
 ipv6 router ospf 1
   router-id 10.10.10.1
 </PRE>